Restore Your Aston Martin Finish In Two Steps Select Your Aston Martin's Color (Step One). AutomotiveTouchup paint products are custom mixed to perfectly match the color of your 2007 Aston Martin DB9 using a basecoat/clearcoat system just like factory specs. To insure a proper match, you’ll need to know your vehicle’s color code so you can find it on the chart below. Most integrators use audio cable (not Cat5) for 9 pins, the color code below is for reference. RTS RJ12 Adam Frame Key Panel The mix of DB9, RJ-12, and RJ-45 inevitably means adapters, these modular versions are very common, I prefer the Star-Tech brand since their color code is consistent and follows standard telco wiring. As other reviewers mentioned, the wire colors are not standard. I ordered two of them and the pinouts were the same for both so maybe they're all configured the same way. In case you need it, the pinout from the RJ45 (Colors following T-568B) to DB9 wires is RJ45 to DB9 Wires 1(OW) - Blue wire 2(O) - Orange 3(WG) - Black 4(B) - Red 5(WB )- Green.
Do you have any idea how much a pieces of Original Cisco Console Cable? Does DIY Cisco Console Cable cheaper?
According to the vendor ,the Original Cisco Console Cable worth approximate RM100 above (60USD++). Usually Cisco console cable only come with each Cisco product you bought, but I found that ebay just sold at around 5USD to 10USD exclude shipping fees, while local website sold at RM60 above.
Should be those user who bough a lot Cisco switches and router, and they only use few to configure their Cisco device.
I was thinking does any Cisco’s Freak out there custom DIY their own Cisco Console Cable? I guess I am one of the “freak” who plan to do it.
Before I get start to DIY Cisco Console Cable, I require to know the arrangement of the cable. Arrangement on the RJ45 pin and another end at DB9 port.
Let study on the serial port numbering location 1st (DB9), and RJ45 numbering location 1st. below are the port number for DB9 connector and RJ45 port number:
DB 9 Port Pin Number
RJ45 Pin Number
The color code for Cisco Console Cable as below:
rj45-1 to db9-8
rj45-2 to db9-6
rj45-3 to db9-2
rj45-4 to db9-5
rj45-5 to db9-5
rj45-6 to db9-3
rj45-7 to db9-4
rj45-8 to db9-7
To confirm the above Cisco Console Cable color code correct, I require to do some verification. I require a Multimeter, mostly I will prefer tone mode, which mean the positive (Red) and negative (Black) touch together, will hv beep sound from the multimeter.
I require a mini gender changer, male to male type, shown as below:
I connected this mini gender changer to the Cisco Console Cable’s Serial Port end as shown the picture below:
I need to use either 1 end of the multimeter to point to the RJ45’s Pin 1, and another end touching each pin on the DB9 serial connector until the beep tone occur. Record down which pin is come from RJ45’s Pin 1 (as above stated, RJ45’s Pin 1 connected to Db9’s Pin 8)
Repeat the same step for RJ45’s Pin 2 until Pin 8, the result will be as above Cisco console cable color code.
After get known all the color code, now you require to get a soldering iron, and also a female db9 connector.
Db9 Cable Color Code
Solder the RJ45 cable to the DB9 Connector according to the cisco console cable color code above
Db9 Pinout Diagram
You can get variety of db9 connector which come with cover, just like as below. I does not know what this kind of connector call, but it is very convenience just to have 1 pcs of this DB9 to RJ45 connector.
If you interested to DIY your own Cisco Console Cable, you can have a try, the above Cisco Colsole Cable color code has been proven correct by me. To ensure all the thing goes smoothly, it is advice to test it your self before you create your own console cable.
Happy “Do it Your Self” Cisco Console Cable.